R a n g e H o o dInstallation Guideand Users Manual
14 15Island Hood InstallationDesigner Wall Range Hood InstallationStep 8Find the center of the wall where you are installing the hood. Make sure there
16 17Designer Wall Range Hood InstallationThe recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop.For Outdoor (30
18 19Under cabinet InstallationPreparationDecide the location of the venting pipe from the hood to the outside. Check hood for clearance. A straight,
20 21Under-Cab Rear Ducting ConversionUnder cabinet InstallationStep 5 Draw electrical wires through cabinet access opening, center the hood beneath t
22 23Range Hood Insert InstallationWhen installing a range hood insert, it is recommended to install the unit at a minimum of 30˝ from the cooktop.For
24 25REMOTE BLOWER INSTALLATION REMOTE BLOWER INSTALLATIONWhen installing your new remote blower type range hood, follow the instructions for the type
26 27REMOTE BLOWER INSTALLATIONThe Remote Blower is designed for our Remote Range Hoods. This unit is installed remotely in the interior of your home.
28 29How to Change PartsHow to Replace the Circuit Board: 1. Turn the power off at the breaker and unplug the Range Hood. 2. Remove all screws from
30 31How to Change PartsProfessional Series Baffle Filter Change: Covering Models 696 / 697 / 697 Island / KECOM / KECOM Island / 695 , 698, and 721 In
32 33Replace or Change Charcoal Filters: It is recommended to direct vent the hood whenever possible. If your situation does not allow for a direct v
CONTENTSIMPORTANT SAFETY INSTRUCTIONS 1WALL RANGE HOOD INSTALLATION 4CROWN MOLDING INSTALLATION 9DESIGNER WALL RANGE HOOD INSTALLATION
34 35Replace or Change Transformer: 1. Remove the screws from the transformer.2. Remove the two connections to the lights.3. Remove the two wired con
36 37How to Change PartsSingle Motor Electrical Diagram: Switch110-120V60HzM~TransformerC2x12Vmax 20Wwhwh whbkbkrdbr buorye16 F/250VhHow to Change P
38 39How to Change PartsButton Control Panel Operation: Button functions Power: Power ON/OFF the range hood and activate power-off delay timer. Li
40 41Trouble Shooting and FAQsWhat type of stainless steel are our hoods made of?Our indoor stainless steel hoods are made with a 430 stainless steel.
42 43Trouble Shooting and FAQsHow do I order replacement parts? Replacement parts can be ordered by contacting our customer service department. All ho
Kitchen and BathTwo Locations: 916 Delaware AvenueMarysville, Ohio 43040350 Parr CircleReno, NV 89512www.zlinekitchen.com1-614-777-5004ZZl ne
1This warranty is valid in the United States. It is non-transferable and applies only to the purchaser and does not extend to subsequent owners of thi
2 3Important Safety InstructionsAll electrical wiring must be properly installed, insulated and grounded.Old duct work should be cleaned or replaced,
4 5Please unpack your range hood when it is delivered and inspect to ensure all parts are included.Parts Supplied1. Main Hood with All Lights and Butt
6 7Step 5Install the transition piece securing it with the screws provided. Figure 4Step 6Make your electrical and ducting connections. Try and minim
8 9Before installing baffle filters, make sure that you insert the grease cup under the motor blower.Step 8Install the two part chimneys on top of the h
10 11Designer Wall Range Hood Installation Designer Wall Range Hood InstallationPlease unpack your range hood when it is delivered and inspect to ensu
12 13The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop.For Outdoor (304 Series) hood installation, the unit
Commentaires sur ces manuels